Ghost Controls Keypad & Intercom Repair Nationwide

Ghost Controls Keypad & Intercom Repair: The Pearland Owner’s Guide

Most Ghost Controls keypad or intercom failures in Pearland run between $145 and $410 to repair, installed, depending on whether we’re replacing a weather-damaged keypad membrane, a dead intercom speaker, or the entire control board. We stock Ghost Controls-compatible parts on the truck and can usually complete the repair the same visit, since we carry the three most common keypad generations and both intercom module styles. The typical call goes like this: the gate works fine with a remote or the app, but the keypad ignores codes, or the intercom has gone quiet on one end, or the whole exterior unit died after a heavy rain.

Call (346) 253-3225

Name what you found. Name what it costs. Name what you left behind. That’s how we document every repair, and it’s exactly what you’ll see on your invoice and photo log before we pull out of your driveway.

Which Ghost Controls Models This Applies To

Ghost Controls has shipped three keypad generations since the company entered the residential gate market: the original ACPD keypad (the older gray-bodied unit), the AXWK wireless keypad series, and the current AWK and AX-series keypads paired with the newest openers like the TDS2, TSS1, and R series. The intercom side is simpler: Ghost Controls offers the AXIC intercom module as a wired add-on, and most Pearland homes with a Ghost Controls opener use either that or a third-party intercom wired into the gate operator’s accessory terminals.

Here’s the compatibility gotcha many homeowners miss: an AXWK keypad won’t talk to a first-generation Ghost Controls board without the ACPD adapter harness, even though the mounting plate looks identical. We see at least one Pearland homeowner a month who bought a used keypad from an online marketplace and paired it to a board that was never going to recognize it. If you flip the keypad over, the model number is molded into the rear housing; send us that number or a photo before we arrive, and we’ll bring the correct part the first time.

On OEM versus aftermarket: Ghost Controls-branded keypads are fine hardware, but the aftermarket equivalents we stock from Linear and Mighty Mule are built to the same weather-sealing spec and usually run $25 to $60 less per unit, so we’ll quote both and let you choose. After ten years of Pearland humidity, the failure point is rarely the circuit board anyway – it’s the silicone membrane under the buttons, which aftermarket kits replace just as well.

Signs Your Ghost Controls Keypad & Intercom Repair Is Failing

• The keypad lights up but the gate won’t move. This usually means the keypad itself is fine and the problem is the code memory or a worn relay on the control board. We’ll test the keypad’s output at the terminal strip before condemning anything.
• The buttons feel mushy, or some work and some don’t. Classic silicone membrane fatigue, especially on south-facing gates in Pearland where the afternoon sun cooks the exterior keypad surface. The membrane hardens, cracks, and individual switch contacts stop closing.
• The intercom rings the house unit but no voice comes through, or vice versa. A shorted speaker coil or a broken wire inside the flex conduit is the usual culprit. We’ve also fixed intercoms that transmit one direction but not the other because the microphone element corroded after storm water wicked up the cable jacket.
• The keypad works after a storm but quits again a day later. Water intrusion. The housing gasket has shrunken and the circuit board is getting damp, then drying out. This one is worth fixing fast, because a corroded board can send low voltage back into the opener and take the whole control unit down with it.
• The intercom buzzes loudly whenever the gate is in motion. Usually a ground loop caused by the intercom and the gate motor sharing a corroded ground lug. We find that on older Pearland installs where the original contractor skipped a dedicated ground wire for the intercom circuit.

Before

After

Replacement Cost & What’s Included

Here’s the range we quote in Pearland, including the part and our labor:

• Keypad membrane replacement only: $145 to $185
• Full keypad replacement (aftermarket unit): $210 to $280
• Full keypad replacement (Ghost Controls OEM): $265 to $340
• Intercom speaker or microphone repair: $160 to $240
• Complete intercom module replacement: $290 to $410

Those numbers include everything: the part, the labor, re-pairing the unit to your opener, testing every code and the intercom both directions, and the photo record. What moves the price is access – if the keypad is mounted on a brick pillar and the wire run needs to be fished, that’s a longer hour than a surface-mounted box on a gate post. You’ll see the written price before we touch a screwdriver. That’s Haven Standard Clause 1, and there is no exception for Ghost Controls work.

Every keypad or intercom repair carries the 365-Day Done Right Promise. If it fails again within a year for the same reason, we’re back out and we make it right at no charge.

DIY or Call Us?

Keypad and intercom work is low-voltage, so the safety risk is minimal compared to gate springs or a motor swap. If you’re handy, there are two things worth trying before you call: check the keypad’s battery or the continuity of the wire at the terminal strip, and inspect the gasket for obvious cracks or shrinkage. That’s five minutes and costs nothing.

Where DIY goes wrong is replacement part matching. Ghost Controls is on its third keypad protocol, as I mentioned above, and we regularly fix gates where a homeowner paired a nice-looking replacement keypad to a board that never had a chance of reading it. By the time you’ve bought the wrong unit twice, you’ve spent more than our labor. If you want to avoid that loop, call us at (346) 253-3225 and we’ll match the part to your board before we even load the truck.

FAQs